01000 6631

RS485 4-wire to sinlgemode converter, DL485-4W

The DL485-4W is a RS485 4-wire to singlemode fiber optic converter for point-to-point connections. For adapter you can make the choice between ST, SC or SC-BIDI. BIDI technology means that you need only one fiber for transmitting and receiving of the data.

Read more

Product variants

Article Number Product Name
01000 6631 + DL-485-4W/13-SM-ST RS485/4-wire/SM + Request quote
DL485-ST, RS485 4-wire converter for point-to-point connections over singlemode fiber optic
01000 6633 + DL-485-4W/13-SM-SC RS485/4-wire/SM + Request quote
DL485-SC, RS485 4-wire converter for point-to-point connections over singlemode fiber optic
01000 6633-BIDI-A + DL-485-4W/13-SM-SC-BIDI RS485/4-wire/SM + Request quote
DL485-SC-BIDI, RS485 4-wire converter for point-to-point connections over multimode fiber optic
01000 6633-BIDI-B + DL-485-4W/13-SM-SC-BIDI RS485/4-wire/SM + Request quote
DL485-SC-BIDI, RS485 4-wire converter for point-to-point connections over single fiber optic
01000 6635 + DL-485-4W/13-SM-E2000 RS485/4-wire/SM + Request quote
DL485-E2000, RS485 4-wire converter for point-to-point connections over singlemode fiber optic

Description

The fiber optic systems DL485 connect field bus systems with RS485 interfaces. Optical linking allows safe data transfer and is suitable for MODBUS, MODNET-1/SFB, BIT-BUS, SAIA-S-BUS and several manufacturer-specific systems.

The fiber optic systems DL485-4W connect field bus systems with RS485 four-wire interfaces.

With the help of this innovative system optical bus, star, tree and mixed structures are possible.

LEDs and potential-free contacts of a fault detector relay are able to signal defective states.

FiberView works similarly to a traffic light. If the “traffic light” is green, everything is fine. If the yellow LED lights, the budget is still tolerable, but already below a certain system reserve. Additionally to the LED, this pre-warning level is also signaled by a potential-free contact. If the “traffic light” turns red there is a serious error. fiber optic systems DL485 connect field bus systems with RS485 interfaces. Optical linking allows safe data transfer and is suitable for MODBUS, MODNET-1/SFB, BIT-BUS, SAIA-S-BUS and several manufacturer-specific systems.

Specifications

Data rate:
1200 Bit/s to 3MBit/s
Transmission type:
Half duplex
FO-connector:
ST, SC, SC-BIDI or E2000
Fiber type:
Singlemode 9/125µm
Optical budget:
16 dB
FO range:
30 km, others up to 100 km on request (0,3 dB/km)
Wavelength:
1310 nm (1310 nm 1550 nm for BIDI)
Terminating resistor:
Switchable: none or wave impedance (Rw + Rpd + Rpu)
RS485 Cable length:
1200 m (9.6 - 93.75 KBit/s), 250 m (500 KBit/s), 90 m (1.5 MBit/s)
RS485 Connector:
9-pole Sub-D female and 6-pole terminal
Status-LEDs:
Power supply (green) / Failure (red) / Data receive (green) / Status (red) / FiberView (red, yellow, green)
Power supply:
12 - 30 VDC, other voltages on request
Power consumption:
5 Watt, 200 mA (24 V)
Galvanic isolation:
500 VDC (24 VDC <> RS485)
Operating temperature:
-40°C to +70°C (Multimode and Singlemode with ST or SC), -20°C to +55°C (all others)
EMC:
EN61000-6-2/EN55022 Class B + A1 + A2
Weight
570 g
Dimensions:
60 x 100 x 113 mm (60 x 120 x 113 mm incl. connector)
Housing:
Stainless steel, powder coated

Do you have a request?

Request type
Art. Nr. Product name Remove

You can add another variation to your request

Do you have a request?